SYT5059-2000-组合泵筒管式抽油泵.pdf

《SYT5059-2000-组合泵筒管式抽油泵.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、1〔575.E:S?备案号SY中华人民共和国石油天然气行业标准SY/1'5059-2000组合泵筒管式抽油泵Tubingpumpwithcombinedliners2000一12一12发布2001一06一01实施国家石油和化学工业局发布SY/f5059-2000目次前言Wl范围··············································································································⋯⋯12引用标准·············

2、·························································································⋯⋯1门j定义··············································································································⋯⋯14规格代号及其表示方法··················································

3、···························⋯⋯““⋯⋯1倪基本参数·········································································································⋯⋯26技术要求·········································································································⋯⋯21了试验方法和检验规

4、则··························································································⋯⋯40凸标志···············································································································⋯⋯5Q包装·......................................................

5、..............................................................6附录A(标准的附录)配合间隙最大漏失量推荐值·····················································⋯⋯7SY/f5059-2000前言本标准是在SY/1'5059-91《抽油泵》的基础上，保留了大部分适用于组合泵筒管式抽油泵方面的内容，增加了相关内容，并根据相关标准的最新版本进行编制的。本标准对组合泵筒管式抽油泵金属柱塞与衬套的配合间隙这一主要技术要素做出了明

6、确规定。另外，还删除了SY/1'5059-91中标称直径为95mm规格的组合泵筒管式抽油泵。本标准从发布之日起，同时代替SY/1'5059-910本标准的附录A是标准的附录。本标准由全国石油钻采设备和工具标准化技术委员会提出并归口。本标准负责起芍单位:玉门石油管理局机械厂。本标准参加起草单位:兰州石油机械研究所、江汉石油机械研究所。本标准主要起草人强生域苟向川李立韩规划时玉明王丽霞殷莉本标准于1985年11月首次发布，于1991年11月第一次修订，此次为第二次修订。中华人民共和国石油天然气行业标准SY汀5059-2000组合泵筒管式抽

7、油泵代替SY/1'5059-91Tubingpumpwithcombinedliners1范围本标准规定了常规组合泵筒管式抽油泵(以下简称组合抽油泵)的基本参数、技术要求、试验方法、检验规则、标志及包装等内容。本标准适用于从油井抽极油液用常规组合抽油泵的设计、制造和检验。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。GB/1'197-1981普通螺纹公差与配合(直径1--355mm)GB252-1994轻柴

8、油GB/1'308-1989滚动轴承钢球GB/1'1804-1992一般公差线性尺寸的未注公差GB/1'9253.2-1999石油天然气工业套管、油管和管线管螺纹的加工、测量和检验SY/1'5029-1995抽油杆(抽油