TBT2710.2-2005机车、动车用空气压缩机技术条件螺杆空气压缩机.pdf

《TBT2710.2-2005机车、动车用空气压缩机技术条件螺杆空气压缩机.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ics45.oso.10s40TB中华人民共和国铁道行业标准TB/T2710.2-2005机车、动车用空气压缩机技术条件第},部分:螺杆空气压缩机TechnicalspecificationforaircompressoronlocomotiveandpowercarPart2:Screwaircompressorwww.bzfxw.com2005-08一19发布2006-01-01实施中华夕L民共和国铁道部发布www.bzfxw.comTB/T2710.2-2006目次青···············································。·······

2、······················⋯⋯、························⋯⋯n围·········································································································⋯⋯1八‘1勺内J64规范性引用文件······································································.............····.........⋯⋯1技术要求··············，

3、·········，················································································⋯⋯1试验方法·········································································································⋯⋯3检验规则·····················································································

4、····················⋯⋯3标志、包装与贮存······································································........·········.........⋯⋯4附录A(规范性附录)压缩空气露点温度图表·····································..........................⋯⋯5附录B(规范性附录)允许偏心距····················································....·······

5、·······....···.⋯⋯6www.bzfxw.comTB/T2710.2-2005前.曰‘.蔺TB/T2710《机车、动车用空气压缩机技术条件》分为两个部分:—第1部分:往复活塞空气压缩机;—第2部分:螺杆空气压缩机。本部分为TB/T2710的第2部分。本部分的附录A、附录B为规范性附录。本部分由铁道行业内燃机车标准化技术委员会提出并归口。本部分起草单位:石家庄国祥精密机械有限公司、中国北车集团北京南口机车车辆机械厂、中国南车集团资阳机车厂、中国北车集团大连机车研究所。本部分主要起草人:徐兵舰、刘功国、姐玉玲、周震贤。本部分为首次发布。www.bzfxw.comTB/T2

6、710.2-200b机车、动车用空气压缩机技术条件第}i部分:螺杆空气压缩机，范围本部分规定了机车、动车用喷油螺杆空气压缩机(以下简称“空压机”)的技术要求、试验方法、检验规则、标志、包装和贮存。本部分适用于机车、动车用风冷、额定排气压力不超过1000kPa的空压机。本部分也适用于工务车、工矿机车、城轨车辆用空压机。2规范性引用文件下列文件中的条款通过TB/T2710的本部分的引用而构成为本部分的条款。凡是注日期的引用文件，其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本部分，然而，鼓励根据本部分达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最

7、新版本适用于本部分。GB150钢制压力容器GB/T191包装储运图示标志GB/T6388运输包装收发货标志GB/T7777-2003容积式压缩机机械振动测量与评价GB/T8539-2000齿轮材料及热处理质量检验的一般规定GB/T10095.1渐开线圆柱齿轮精度第1部分:轮齿同侧齿面偏差的定义和允许值GB/T12243-1989弹簧直接载荷式安全阀GB/T13306标牌GB/T13384机电产品包装通用技术条件GB/T15115-1994压铸铝合金GB/T15116-