DBJ 43T 311-2015 装配式斜支撑节点钢框架结构技术规程

《DBJ 43T 311-2015 装配式斜支撑节点钢框架结构技术规程》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、湖南省住房和城乡建设厅文件湘建科〔2015〕53号湖南省住房和城乡建设厅关于发布湖南省工程建设推荐性地方标准《装配式斜支撑节点钢框架结构技术规程》的通知各市州住房和城乡建设局(建委、规划建设局)，各有关单位：由远大可建科技有限公司、北京工业大学主编的《装配式斜支撑节点钢框架结构技术规程》已由我厅组织专家审定通过。现批准为湖南省工程建设推荐性地方标准，编号为DBJ43／T311—2015，自2015年8月1日起在全省范围内执行。该标准由湖南省住房和城乡建设厅负责管理，由主编单位远大可建科技有限公司、北京工业大学负责标准具体技术内容的解释。湖南省住房和城乡建设厅

2、2015年5月6日学兔兔www.xuetutu.com前言根据《关于印发湖南省住房和城乡建设厅2012年科学技术项目计划的通知》（湘建科函〔2012〕409号）的要求，规程编制组经广泛调查研究，认真总结实践经验，参考有关国际标准、国外先进标准和国内有关标准，并在广泛征求意见的基础上，制定本规程。本规程的主要技术内容是：1.总则；2.术语及符号；3.基本规定；4.材料；5.结构设计；6.节点设计及构造；7.构件制作与运输；8.安装与施工；9.防腐与防火；10.工程验收。本规程由湖南省住房和城乡建设厅负责管理，由主编单位负责具体内容的解释。规程执行过程中如有意见

3、或建议，请寄送主编单位远大可建科技有限公司（地址：湖南省岳阳市湘阴县可建城认证政策部，邮编：410600）。本规程主编单位：远大可建科技有限公司北京工业大学本规程参编单位：湖南大学中南大学湖南省建筑设计院中机国际工程设计研究院有限责任公司中国轻工业长沙工程有限公司湖南省第六工程有限公司湖南省建筑材料研究设计院有限公司·1·学兔兔www.xuetutu.com主要起草人员：张跃张爱林谭永强刘学春舒兴平杨建军刘冬柏张友亮江山红壮真才周一平周湘江朱智俊梅智钧梁翠柳主要审查人员：沈蒲生陈禄如陈浩王明贵刘玉辉陈宝武朱晓鸣周岚任卫红·2·学兔兔www.xuetutu.c

4、om目录1总则············································································12术语及符号······································································22.1术语·······································································22.2符号·······································

5、································33基本规定·········································································53.1结构体系的一般规定·····················································53.2结构布置····································································63.3位移限值和舒适度要求···············

6、··································83.4抗震等级··································································104材料···········································································124.1结构材料··································································124.2连接材料··········

7、························································124.3防护材料··································································144.4其他材料··································································145结构设计·····································································

8、···165.1设计原则··············