JJF1108-2003石油钻具接头螺纹工作量规、圆螺纹套管工作量规和油管螺纹工作量规校准规范.pdf

《JJF1108-2003石油钻具接头螺纹工作量规、圆螺纹套管工作量规和油管螺纹工作量规校准规范.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华人民共和国国家计量技术规范JJF1108-2003石油钻具接头螺纹工作量规、圆螺纹套管工作量规和油管螺纹工作量规校准规范CalibrationSpecificationforWorkingGaugeofRotaryShoulderedConnections,RoundThreadCasingandTubing2003一09一23发布2003一12一23实施国家质量监督检验检疫总局发布工1F1108-2003石油钻具接头螺纹工作量规、圆螺纹套管工作量规和油管夕.O.O.0.0.O.O.O.O.O.O.O.O.O.O.飞乙0螺纹工作量规校准规范}，1108-2003{弓仑Calibr

2、ationSpecificationforWorking、.o.0.o.o.o.o.0.o.o.0.0.0.0.。护GaugeofRotaryShoulderedConnections,RoundThreadCasingandTubing本规范经国家质量监督检验检疫总局于2003年09月23日批准，并自2003年12月23日起施行。归口单位:全国几何量长度计量技术委员会主要起草单位:中国计量科学研究院参加起草单位:中国石油天然气集团石油管材研究所上海宝山钢铁集团公司钢管厂宝鸡石油机械厂天津钢管公司本规范委托归口单位负责解释.TJF1108-2003本规范主要起草人:薛梓(中国计量科学

3、研究院)王正强(中国计量科学研究院)参加起草人:卫尊义(中国石油天然气集团石油管材研究所)朱富林(上海宝山钢铁集团公司钢管厂)段旭峰(中国石油天然气集团宝鸡石油机械厂)冉桂芬(中国石油天然气集团宝鸡石油机械厂)李士臣(天津钢管公司)JJF1108-2003目录1范围·········································································，················⋯⋯(1)2引用文献·。····························································

4、······················⋯⋯(1)3概述··························································································⋯⋯(1)4计量特性····················································································⋯⋯(1)4.1表面粗糙度····································································

5、··········⋯⋯(1)4.2钻具接头螺纹工作量规计量特性···················································⋯⋯(1)4.3圆螺纹套管工作量规和油管螺纹工作量规计量特性···························⋯⋯(1)4.4结构尺寸要求···········································································⋯⋯(3)4.5外观要求······················································

6、···························⋯⋯(3)5校准条件····················································································⋯⋯(3)5.1校准用仪器设备········································································⋯⋯(3)5.2校准环境···········································································

7、········一(3)6校准项目和校准方法·····················。···············································⋯⋯(4)6.1钻具接头螺纹工作量规的校准项目················································⋯⋯(4)6.2圆螺纹套管工作量规、油管螺纹工作量规的校准项目··························一(4)6.3外观检查