GBT18335-2001 有贯穿连接的刚挠多层印制板规范.pdf

《GBT18335-2001 有贯穿连接的刚挠多层印制板规范.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS31.180L30署8中华人民共和国国家标准Gs/T18335-2001idtIEC60326-11:1991有贯穿连接的刚挠多层印制板规范Specificationforflex-rigidmultilayerprintedboardswiththroughconnections2001一03一07发布2001一06一01实施国家)贡At技术业气督局发布标准分享网www.bzfxw.com免费下载Gs/T18335-2001目次前言··························································

2、···············································“····⋯⋯工IEC前言··⋯，’’·····································”···················”···················，.····················“⋯1IEC引言···········································································································

3、·⋯⋯II1范围···································“···································”····································⋯⋯12引用标准·······························································································”····⋯⋯13总则··················································

4、·························································⋯⋯14试样，········································································”······“·························⋯⋯15有关规范···········..······································“················“······················”·······⋯⋯16

5、印制板的性能···········································································..····“················⋯⋯27测试图形—测试板···········。··································。················⋯⋯;..·················⋯⋯10Gs/'r18335-2001前言本标准等同采用IEC60326-11:1991《有贯穿连接的刚挠多层印制板规范》。本标准涉及的刚挠多层印制板多用于精

6、密电子设备和仪器，具有体积小、重量轻、安装灵活、工作可靠等特点。本标准由中华人民共和国信息产业部提出。本标准由全国印制电路标准化技术委员会归口。本标准由华北计算技术研究所负责起草。本标准主要起草人:陈长生、汤燕闽、张春婷、刘摘o标准分享网www.bzfxw.com免费下载GB/T18335-2001IEC前言1)IEC(国际电工委员会)在技术问题上的正式决议或协议，是由对这些向题特别关切的国家委员会参加的技术委员会制定的，对所涉及的问题尽可能地代表了国际上的一致意见。2)这些决议或协议，以推荐标准的形式供国际上使用，并在此意义上为各国家委员会所认可。3)

7、为了促进国际上的统一，IEC希望各国家委员会在本国条件许可的情况下，采用IEC标准的文本作为其国家标准。IEC标准与相应国家标准之间的差异，应尽可能在国家标准中指出。本标准由IEC第52技术委员会(印制电路)制订。本标准文本以下列文件为依据:六个月法表决报告二个月法表决报告52(C0)31052(C0)32652(C0)33352(C0)342表决批准本标准的详细资料可在上表列出的表决报告中查阅。IEC引言IEC60326涉及准备安装元件的印制板，而不考虑它们的制作方法本标准分为几个独立的部分，包括设计者用的信息，供规范制定者用的建议以及各种类型印制板(

8、如单面双面、多层及挠性印制板)的试验方法和要求。中华人民共和国国家标准有贯穿连接